May_EDFA_Digital
edfas.org 1 1 ELECTRONIC DEVICE FAILURE ANALYSIS | VOLUME 20 NO. 2 in white. The crosstalk present in the yellow waveform disappears when the probe is moved from the yellow to the blue position. Additional toggles appear in the yellow waveform—due to modulations from the neighboring transistor—and occur at a different time interval. Complexity further increaseswhen the transistors con- nected to each other are in close proximity and create a convolutedwaveform. Here, changing patterns or inspect- ing upstream and downstream signals may not help if these transistors are in the same path and thus toggle during the same time interval. Such cases cause difficulty in predicting the logic state of a single node, as one can observe additional troughs or peakswithin the same logic state. This leads to incorrect interpretations and false conclusions during LVP. While it may not be possible to separate the modulations in time or space, it is possible to look at the waveforms from the group of transistors as a whole, rather than as individual transistors. Very often, a group of related transistors form a more complex unit and perform a particular operation. We refer to these as combinational cells or logic gates. A careful way to study combinational cells is to com- prehensively investigate the electrical conditions of every node within the optical probe with techniques such as spice models, [8] but such resources may not be readily available to the failure analysis (FA) engineer. Here, the authors share the technique of combinational logic analysis (CLA) using laser voltage probing. [9,10] The process consists of developing a library of waveforms by observing simple combinational elements such as NAND and NOR gates and correlating the waveforms to a corresponding truth table. CLAas presented in this article offers significant advan- tages over the conventional process. REDUCED NEED FOR RESOLUTION The generally accepted resolution requirement [11] for LVP is about two or three times the contacted poly pitch (CPP), which is the distance between the source and the drain contacts of a transistor at a particular technology. This forces a constant search for resolution improvement with technology, by migrating to higher numerical aper- ture solid immersion lenses ( NA SILs) or shorter probing wavelengths, both of which have stringent sample prepa- ration requirements. Multiple short wavelength tools have been developed over the past few years and the residual silicon thickness (RST) needs are between 1 and 5µm. [12-14] Such ultra-thin samples bring about challenges for sample preparation, as well as thermal and mechanical stability. The thermal and mechanical stability of such samples has not been completely characterized, but initial investigations [15] are concerning. These challenges make sample preparation for short wavelength light probing undesirable, especially if the failing sample is a qualifica- tion reject or a customer return. CLAworks by considering convolutedwaveforms from the entire combinational logic cell instead of individual transistors, thereby reducing the raw resolution require- ment imposedby LVP.While it is not possible to completely overcome the resolution constraints, CLA has potential within its limited scope to determine if cell functionality is affected by a defect. FASTER AND MORE RELIABLE The CLAprocess is quite often faster than conventional LVP. Scan logic testing for the structural test of digital cir- cuits is limited by the efficiency of the test vectors. [16,17] To effectively test all input combinations, multiple iterations of vectors are required, whichmakes the LVP process long and tedious. The problem is exacerbatedwhen the failing signature is a logical mismatch that requires specific input vectors for stimulating the failure. Observing toggles within an LVP waveform does not always mean that the observedcell is functional. CLAensures that everypossible input combination of the cell is observed, and by doing so, reliably assesses cell functionality. CLA PROCESS PATTERN For effective CLA, as with LVP, appropriate patterns are required to be looped by the tester. The authors employ generic scan patterns, which are used in standard structural testing for modern digital circuits. The primary advantage of using scan is that scan flops are connected directly or indirectly—through a combinational path—to almost every digital net within the IC as shown in Fig. 2. By using a single load pattern with LVP, it is usually pos- sible to capture enough input combinations to evaluate the entire truth table. THE OPTICAL PROBE The optical probe size of LVP is usually limited by the resolution of the tool. [12] The distribution of laser power within the target spot is typically Gaussian but can be altered by polarization, wavelength, and numerical aper- ture. This laser profile affects the number of transistors modulating the laser, aswell as the strengthofmodulation of each node under the probe. Consequently, the position of the probe within the cell also significantly affects the resultant waveform. Caremust be taken to collect signals
Made with FlippingBook
RkJQdWJsaXNoZXIy MjA4MTAy