May_EDFA_Digital

edfas.org 15 ELECTRONIC DEVICE FAILURE ANALYSIS | VOLUME 20 NO. 2 cell. Waveforms were collected from the PMOS drivers of each of the cells and are shown in Fig. 4b. The output of the NOR shows sharp transitions and flat levels, which usually occur on good transistors. However, through CLA (Fig. 4c), three states were expected, but were completely missing. This mismatch in the LVP state indicated that the NOR gate contained a defect, a metal short verified by physical FA. This case study shows that waveforms with flat states and sharp transitions, which are usually exhibited by good nets, could still be defective. Therefore, a thorough investigation of the cell, by observing all input combinations, is necessary to ensure functionality. An exhaustive truth table construct helps identify the cycles at which the signal clearly does not match expectations, thereby further isolating the potential failing locations. Finally, an entire analysis could be completed using just three waveforms from each of the output drivers, under- lining the efficiency of this process. CONCLUSIONS Shrinking technology footprints create increasing spatial resolution challenges for laser voltage probing. It is useful to consider signals frommultiple transistors within combinational elements at the same time. Combinational logic analysis is a process by which LVP signals for com- binational elements such as NOR and NAND are better understood. This process speeds up laser voltage probing, despite restrictions in spatial resolution. In addition to accelerating the process, it increases the reliability of fault isolation and helps to further narrow down the defect. REFERENCES 1. J.M. Chin, et al.: “Fault Isolation in Semiconductor Product, Process, Physical and Package Failure Analysis: Importance and Overview,” Microelectron. Reliab., 2011. 2. V.K. Ravikumar, et al.: “Laser Voltage Probing in Failure Analysis of Advanced IntegratedCircuits on SOI,” Proc. Int. Symp. Phys. Fail. Anal. Integr. Circuits (IPFA), 2011. 3. Y.S. Ng, et al.: “Laser Voltage Imaging: A New Perspective of Laser Voltage Probing,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2010. 4. T. Parrassin, et al.: “Laser Voltage Imaging and Its Derivatives, Efficient Techniques to Address Defect On 28 nm Technology,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2013. 5. V.K. Ravikumar, et al.: “Laser Voltage Tracing for Electrical Fault Isolation of Circuits Propagating Aperiodic Signals,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2017. 6. U. Kindereit, “Fundamentals andFutureApplications of Laser Voltage Probing,” Proc. IEEE 52nd Ann. Int. Reliab. Phys. Symp. (IRPS) , 2014. 7. W. Lua, et al.: “Systematic Root Cause Analysis of Metal Defects in FINFET Devices,” Proc. Int. Symp. Phys. Fail. Anal. Integr. Circuits (IPFA), 2017. 8. E. Abuayob, et al.: “ComplexWaveformAnalysis for Advanced CMOS ICs: Physics of ComplexWaveformSignals for Design Validation and Debug Application,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2016. 9. V.K. Ravikumar, et al.: “Combinational Logic Analysis using Laser Voltage Probing,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2015. 10. W. Lua, et al.: “Combinational Logic Analysis Case Studies Using Laser Voltage Probing,” Proc. Int. Symp. Phys. Fail. Anal. Integr. Circuits (IPFA), 2016. 11. M.V. Haartman, et al.: “Optical Fault Isolation and Nanoprobing Techniques for the 10 nm Technology Node and Beyond,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2015. 12. J. Beutler, et al.: “Visible Light LVP on Bulk Silicon Devices,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2015. 13. N. Leslie and C. Nemirow: “The Effects of Using 785 nm for Laser Probing,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2017. 14. T. Eiles and P Pardy: “Visible Laser Probing (VLP) with GaP Solid Immersion Lens Demonstrating 110 nmResolution inCommon Laser Probing Applications,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2016. 15. M.M.Mulholland,etal.:“SamplePreparationTechniquesforReduced Lateral Heat Distribution and Implications for Non-IR Probing on Integrated Circuits,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2017. 16. V.K. Ravikumar: “Understanding Testing for Dynamic Fault Isolation of Microprocessors,” Proc. Int Symp. Phys. Fail. Anal. Integr. Circuits (IPFA), 2016. 17. C. Burmer, et al.: “Timing Failure Debug using Debug-Friendly Scan Patterns and TRE,” Proc. Int. Symp. Test. Fail. Anal. (ISTFA), 2008. ABOUT THE AUTHORS Venkat Ravikumar is a seniormember of the technical staff at AdvancedMicroDevices (AMD) and spent the past decade working on fault isolation at the Device Analysis Laboratory. His key expertise is in bring-up and use of tester-based fault isolation techniques such as photon emission, soft defect localization, and timing analysis tools, such as time-resolved emission, laser voltage probing, and its derivatives. Graduating from the National University of Singapore with an M.S., he is currently pursuing a Ph.D. at Singapore University of Technology and Design, in addition to his role at AMD. Winson Lua receivedhis joint M.Sc. degree inmicroelectronics fromNanyang Technological University and Technical University of Munich in 2011. He has several years of experi- ence in both electrical and physical failure analysis froma technology node of 0.18 µmdown to 40 nm devices. He is currentlywith AMD’s Device Analysis Laboratory, responsible for dynamic fault isolation on the latest FFET devices. His key interest is on the development of fault isolation techniques, and since 2016, he has published two papers on combinational logic analysis with laser voltage probing.

RkJQdWJsaXNoZXIy MjA4MTAy