February_EDFA_Digital
edfas.org ELECTRONIC DEVICE FAILURE ANALYSIS | VOLUME 20 NO. 1 include depleted uranium in caseswhere ultimate stiffness is desired. The question-and-answer session addressed the minimummachining radii achievable for pocket mounting using milling tools, and an extension below 50 µm radii enabled with laser machining techniques. “Thin, Smooth, and Curvy—The Confessions of a Sample-Prep Specialist” was presented by Jim Colvin of FA Instruments, Inc. Jim addressed the need for increas- ingly controlled sample preparation across complex devices that is driven both by new failure analysis meth- odologies as well as increased tolerances for other testing re- quirements. He reviewed sel- ected cases where success- ful processes occurred. Data showing the “orange-peel” effect as a functionof tempera- turewere reviewed, and it was demonstrated that mitigation could occur as the tempera- ture was increased from 20 to 80 ºC within the detection limits of backside optical microscope inspection. The orange-peel effect was interpreted as the residual Z -strain resulting from the C4 attach process, which is particularly easily observed when remaining silicon thickness is below 5 µm. Some applications for capacitive and resistive end- pointing mechanisms were highlighted, and the potential direction for in situ “probing while sample preparing” methodologywas also shared. The audience initiated some discussion on the observable-by-eye color change that occurs when silicon is thinned to single-digit remaining thickness, with disagreement as to whether this obser- vation could lead to development of simpler thickness metrology methodologies. “Effective Microwave-Induced Plasma Decapsulation for Advanced ICPackages”was presented by Erik Jordan of Nisene Technology Group. The discussion focused on limi- tations due to extended throughput time or incompatibility with emergingmaterials systems facing traditional reactive ion etching processes. Also presentedwas the potential for application of microwave-induced plasma deprocessing to include oxygen, argon, carbon tetrafluoride, or other process gases as a solution to the decapsulation require- ments roadmap. Examples from copper/palladium bonds that are highly reactive towet deprocessingwere reviewed in addition to examples demonstrating the deprocessing workflows for emerging silver bonding materials systems. “Wire BondConnectedHigh-BandwidthMemory Attach on 3-D Stacked Die for Physical Debug Sample Prep” was presented by Nathan Bakken on behalf of Charles Ladwig, both of Intel Corporation. Heterogeneous integration of multiple dice at the package level was shown to be an increasingly common and threatening trend for physical debug techniques that traditionally rely on direct access to the backside silicon substrate. When dice are stacked or keep-out-zones required for physical debug techniques are otherwise infringed upon, it was proposed that an opportunity to reassemble die components in an orientation or workflow order suitable for debug could be pursued. Case studies were reviewed, including die reattach post- circuit-edit workflowaswell as direct-to-die attach of LPDDR4 to enable optical probing of the base die in a package-on- package configuration where access to memory channels was a requirement for the fault isolation workflow. Following the presenter topics, themoderators enabled a round-robin discussion of the five-year challenges fore- casted for the sample-prep and 3-D package community. The audience participated by alternating between descrip- tions of future challenges and the relative magnitude of these challenges, with results tabulated and debated in real-time. As a result of a few dozen inputs from a variety of industry experts, seven challenges were identified for sample-prep and 3-D packaging technologists over the next five years: • Absence of a roadmap consortium • Proliferation of manufacturable processes out of the research and development lab • Reduction of the quantity of and artistry required for process steps • Attracting the next generation of engineering talent • Getting support from design-for-test partners • Reducing invasiveness • Enabling budgets The session successfully generated discussion and knowledge-sharing for over 75 people in attendance. “THE SAMPLE-PREP USER GROUP, SPONSORED BY VARIOSCALE, INC., HOSTED FOUR TECHNICAL PRESENTATIONS TOWARD THE DEVELOPMENT OF NEW CAPABILITIES IN THE LABORATORY.” S - 6
Made with FlippingBook
RkJQdWJsaXNoZXIy MjA4MTAy