February_EDFA_Digital

edfas.org 35 ELECTRONIC DEVICE FAILURE ANALYSIS | VOLUME 20 NO. 1 up at V in2 , and V in1 < V in2 . The external start-up delay time consists of input ramp line voltage time from V in1 to V in2 and charging time of the capacitor C4. Parameters of this circuitry vary significantly for different manufacturers’ DC/DC converters. EXPERIMENTAL RESULTS This start-up overshoot is verified in a 5 V rated output hybrid DC/DC converter application circuit. The hybrid DC/DC converter’s start-up waveform without EMI filter or ICSC is shown in Fig. 3. There is no start-up overshoot voltage for the DC/DC converter alone, as stated before. The start-up delay time, T d , is approximately 220 µs, and the start-up time, T s , is approximately 300 µs. Start-up delay time, T d , plus start-up time, T s , is 520 µs. As Fig. 4 shows, however, there is a start-up overshoot when this DC/DC converter is applied in the power system with an EMI filter and ICSC. The overshoot is 3.28 V, which is 65.6% of the rated output voltage. The converter’s load chip failed after start-up for more than 100 times. The working time of ICSC is approximately 3 ms, longer than time T d plus T s . This article adopts the start-up overshoot sup- pression circuitry shown in Fig. 2. This start-up overshoot, which is shown in Fig. 5, is suppressed from 3.28 V to 87.5 mV, from 65.6 to 1.75%. Start-up delay time is increased to approximately 4 ms. SUMMARY When the external ICSC’s working time is longer than the DC/DC converters’ start-up delay time plus start-up time, a start-up overshoot is induced. This is because the DC/DC converter cannot decrease its duty cycle as the ramp input line voltage increases in time. By increasing the DC/DC converter’s start-up delay time, overshoot can be suppressed. A start-up delay circuit is proposed. Experimental results verified its feasibility for suppressing this start-up overshoot voltage. ACKNOWLEDGMENTS The author would like to thank his colleagues Wang Xiaowen, Ma Wenbo, Liu Kecheng, and Wang Weiguo for their work and helpful suggestions. REFERENCES 1. J. Li, M. Yang, W.F. Sun, X.X. Lu, S. Xu, and S.L. Lu: “A Fast Novel Soft-Start Circuit for Peak Current-Mode DC-DC Buck Converters,” J. Semiconduct., 2013, 34 (2), pp. 025006-1–5. 2. K.C. Chang and C.L. Wey: “A Fast Hysteretic Buck DC-DC Converter with Start-Up Overshoot Suppression Technique,” 2012 Asia Pacific Conference on Postgraduate Research in Microelectronics and Electronics (PRIMEASIA), BITS Pilani Hyderabad Campus, Dec. 2012, pp. 56-60. 3. A.P. Yao, H.X. Li, J.Y. Zhang, and L. Wang: “A Novel On-Chip Soft- Started DC-DC Buck Converter for Biomedical Applications,” Proc. IEEE-EMBS. 4. International Conference on Biomedical and Health Informatics (BHI 2012), Hong Kong and Shenzhen, China, Jan. 2012, pp. 806-09. 5. Y.X. Liu, S.B. Liu, Y.M. Li, andW.G. Feng: “Highly Integrated Soft-Start Circuit for DC-DC Switching Converters,” J. Huazhong Univ. Sci. Technol. (Natural Science Ed.), 2011, 39 (2), pp.108-11. ABOUT THE AUTHOR Guo Xianxin is an electrical engi- neer for Chinese spacecraft. He has more than6 years of switchingpower supply research and development experience. His research interests include low-voltage high-current DC/ DC converters, pulse power supply, high-voltage low-current power sup- plies, and adjustable switching power supplies. Mr. Guo received a B.S. degree in electronic engineering from the China University of Mining and Technology in 2007 and an M.S. degree in power electronics from the China Academy of Space Technology in 2010. He is currently pursuing a Ph.D. degree in power electronics at the China Academy of Space Technology. Advertise in Electronic Device Failure Analysis magazine! For information about advertising in Electronic Device Failure Analysis , contact Erik Klingerman, National Account Manager; tel: 440.840.9826; e-mail: Erik.Klingerman@asminternational.org . Current rate card may be viewed online at asminternational.org/mediakit.

RkJQdWJsaXNoZXIy MjA4MTAy