February_EDFA_Digital
edfas.org ELECTRONIC DEVICE FAILURE ANALYSIS | VOLUME 20 NO. 1 32 DC/DC CONVERTER FAILS TO START UP WITHOUT OVERSHOOT DUE TO INTERACTION WITH INRUSH CURRENT SUPPRESSION CIRCUITRY Guo Xianxin, Lanzhou Institute of Physics, Lanzhou, China guoxianxin@126.com EDFAAO (2018) 1:32-35 1537-0755/$19.00 ©ASM International ® INTRODUCTION A chipmay suffer failure due to voltage stress, current stress, temperature stress, mechanical stress, and so on. DC/DC converters work in a control loop to convert the output error signal into a variable duty cycle of the driving signal for the switching element. At start-up, the error amplifier works in anunbalanced state and the pulse widthmodulationworks at 100%duty cycle, thus causing an output overshoot voltage and high input inrush cur- rent. [1] The DC/DC converter’s start-up overshoot voltage will impose a voltage stress on its load chip through the chip’s supply voltage pin and is handled by the power supply designer. So far, a great deal of attention has been given to suppressing start-up overshoot voltage. To achieve this, a soft-start circuit is required. The two most common methods are to adopt an external soft-start capacitor or soft-start capacitor-based circuit and an on-chip digital soft-start circuit. [2-4] Generally, there is no start-up overshoot in a DC/DC converter. However, there is an amazingly high input inrush current when an electromagnetic interference (EMI) filter is applied. This high inrush current mainly involves charging of input capacitors. As shown by the literature, [5] if the power is applied as a step with a rise time of 1 µs or less, the initial inrush current can be 50 A or more on an unlimited power bus. This could occur if power is applied with a switch, such as a relay, on the power bus, leading to possible damage to the power bus and the switch. In a high-reliability space application, inrush current sup- pression circuitry (ICSC) is important and necessary to suppress the inrush current to a reasonable limit at start- up. The inrush current decreases as the working time of the ICSC increases. The typical specification for ICSC’s working time is not more than 5 ms. The start-up delay time of some DC/DC converters plus the start-up time is generally less than 2 ms, shorter than the working time of the ICSC. The transient response performance of DC/ DC converters is limited, with transient response recovery time generally 300 µs. There may still be a start-up overshoot voltage when a DC/DC converter without start-up overshoot itself is applied with ICSC, if the converter does not match its ICSC. The amplitude anddurationof theovershoot voltage varies significantlywith the respective performance of the DC/DC converter and ICSC. This start-upovershoot voltage also imposes a voltage stress to theDC/DCconverter’s load chip and even causes chip failure, whichwas confirmedby a professional reliability research and analysis institute, thus degrading or damaging the entire electronic system. This article explores why a DC/DC converter without start-up overshoot itself fails to work normally, how the start-up overshoot voltage occurs, but not how the start- up overshoot voltage stress leads to chip failure. Solutions are also given in this article. INTERACTION OF DC/DC CONVERTER WITH ICSC In Chinese space electronic systems, ICSC is required to suppress the input inrush current. ICSC is used as a series-limiting resistive element in either the posi- tive or return supply line between the input point and the capacitors, through which the input capacitors are charged when the power bus is applied to the converter. Thus, the input inrush current is limited to a reasonable value. ICSC is always conducted in one of three methods: resistor, negative temperature coefficient thermistor, and active circuit. Active ICSC is based on either an n -channel MOSFET in the return supply line or a p -channel MOSFET
Made with FlippingBook
RkJQdWJsaXNoZXIy MjA4MTAy